Nobody knows more about windows.
Mark Meshulam is a glass consultant for glass failures including foggy windows.
Insulated glass, sometimes called by the old LOF trade name Thermopane, has been commercially offered in the United States since the 1950s. For the ensuing 60 years, the fundamental concept hasn’t really changed.Insulated glass still consists of two or more pieces of glass which are bonded to, yet separated from one another through the use of a spacer at all four edges. The space between them becomes an insulating “dead air space”. This sandwich is glued together with sealants designed to keep the glass together and moisture out. The spacer contains a dessicant that removes moisture which might be residual from manufacturing. Insulated glass seal failure occurs when moisture penetrates the edge seals and wets the airspace.
Thermal Improvement with Insulated Glass
The resulting assembly in its simplest form reduces heat loss by about one half over single glass. For you R-value fanatics, by insulating the glass, we improve the R1 of single glass and to a whopping R2 for insulated glass. When we add a Low-E coating, we can get about R3. If we then add argon gas in the airspace, about R4 is possible.
Insulated Glass Seal Failure
Despite a respectable track record for insulated glass in general, naturally there are failures. A moderate failure will look like a cloud of moisture that has condensed on one of the inner surfaces of the glass in the airspace. It might come and go depending on the outside temperature. This failure is also called “fogging glass”, “foggy window” or “window condensation between panes.”
A serious failure will involve the permanent presence of moisture in the airspace as you can see to the right. Animated glowing is just for entertainment and only occurs in real life when a cloud goes by very quickly, or during frat parties.
The worst failures I have seen also involve degradation of the spacer. Sometimes the spacer corrodes or even rusts. Sometimes the dessicant becomes so saturated that it turns to mush and becomes visible on the spacer. I have even seen a failure in which, upon deglazing, one lite of glass completely separated from the spacer. See this disaster below.
Fixing Insulated Glass Failures
When seal failures occur, the glass must be replaced. There are vendors out there who attempt to fix the failed unit by drilling holes in the spacer, forcing dry air into the airspace, and resealing the hole (or even leaving it open), but future failures are likely. In some instances the glass cannot be cleaned of the stain from the condensation. It’s hard to imagine the total failure shown above repaired without replacement. If any readers have experience with this process, or if you make your living performing it, please write in with your experiences.
Types of Insulated Glass Spacers
These ubiquitous spacers can be made from stainless steel or aluminum. Most are a rectangular tube in cross section, and the dessicant is inside the tube. Dessicant consists of tiny beads. Perforations in the airspace side of the tube allow moisture in the airspace to eventually migrate to the dessicant. Corners of these spacers are either bent or fitted into “corner keys”.
Thermal break spacers
This new family of spacers uses a polyurethane thermal break, just like aluminum window frames. Two separate tubes carry the dessicant beads. This is one variation of “warm edge” technology, which means that on cold days, the interior temperature at the edge of the glass will be similar to the best temperature, considered to be at the center of the glass. I have not yet seen wide adoption of this design here so far. One manufacturer is Azon. They are a force in the thermal break market and naturally evolved their product to work inside the glass as well as in the frame.
Thermoplastic spacers, TPS
These spacers are a solid rectangular cross section of a plastic material that has dessicant entrained within it (Edgetech). Sometimes these spacers also contain a thin corrugated metal fin that assists in maintaining the dimension between the two lites (Tremco Swiggle). Sometimes these spacers are literally extruded right onto the glass edge in a semi-plastic state (Bystronic). Once the thermoplastic spacers are applied to one lite, the second lite is then placed, and the entire assembly goes through pinch rollers into an oven for fusing and curing. Thermoplastic spacers are considered to utilize “warm-edge technology”.
Dessicants are necessary in insulated glass units because of the near impossibility of sealing an insulated unit with perfectly dry air, and to allow for small amounts of moisture permeance during the unit’s service life. Generally, dessicants adsorb, rather than absorb the free-floating moisture in the airspace. In adsorption, the water molecules adhere to the surface of the dessicant rather than permeating into the dessicant as would occur in absorption. I really like the technical name for this process: “molecular sieve”. Cool, huh?
Primary SealThe primary seal is responsible for keeping water out. The hands-down favorite for this seal is PIB, or polyisobutylene. It is a synthetic rubber that is gas impermeable, and so it is able to resist airborne moisture (water vapor) for many years if applied properly.
The job of the secondary seal is to hold it all together. Strength, flexibility and a strong adhesive bond are essential. Polysulfides, a family of carbon and sulfur-based synthetic rubbers have been used for many years. In the last few decades, silicone sealants have experienced increasing popularity. Silicone is similar to quartz, except that some of the oxygen molecules are substituted with carbon-hydrogen groups (methyl – CH3). to create long strands of flexible, durable material. Both have two-part rapid-set versions for factory production use.
One key element of seal longevity is edge deletion. This is the grinding off of coatings such as low-e coatings for a stripe along each edge to allow for direct adhesion to the glass. Edge deletion also keeps the coatings, which are metallic, as far away from the outside air as possible to avoid the possible creep of corrosion beneath the adhesive bond line.
Types of edge seal failures
If you have been diligently reading these articles, especially this one, you will not be surprised to find that failures of insulated glass seals mirror failures that we see in sealants in general. They are:
- Adhesive failure – the sealant stops sticking to the glass
- Cohesive failure – the sealant tears or ruptures within its own boundaries
- Localized puncture or absence of sealant
- Sealant Reversion – the sealant decides to revert back to its prior form or degrade into a totally new and useless form, that is, if the sealant could “decide” things.
Why does seal failure occur?
If the failure occurs within the first few years, there was an error in manufacture or installation. The manufacturer may have used old material or failed to properly mix or apply the sealant. The glass unit may have been moved too soon, disrupting the seal before sufficient cure. There may be sealant incompatibilities between the various sealants, even the setting blocks, used in the glazing system. The manufacturer, shipper or installer may have punctured the seal at any point along the way.
If the seal failures occur after a couple of years following installation, it’s time to look at the drainage system beneath the glass. Weep holes are notoriously absent from most wood and wood-clad windows and even some aluminum windows.
As the glazing seals (between glass and adjacent frame) loosen up, water enters that area and accumulates beneath the bottom of the glass. Without a “weepage path”, this is DOOM, do you hear me? CERTAIN DOOM!!! Doom that could have been avoided if the manufacturers designed a way for the glass to drain. Insulated glass seals are not designed for immersion. These are not aquarium sealants.
In my humble, unbiased and completely objective view, absence of a weepage path beneath the glass has been the single most glaring, persistent weakness in window products since the advent of insulated glass. If you have been a victim of this design/manufacturing shortcoming, I hope you will contact me.
Need a glass consultant for a problem with fogging glass, foggy windows, condensation between panes or glass failure?
Construction & Glass Consultant
Expert Witness, Testing Agency
Window Water Leak Testing
Window Consultant for Architects, Engineers and Building Owners
Condensation Investigation & Testing for Windows and Buildings
Expert Witness & Investigation of Window Falls
Expert Witness & Investigation of Glass Injury
Glass Consultant for Architects, Engineers and Building Owners
Masonry & Wall Moisture Intrusion Investigation & Testing
Air Infiltration Testing for Windows & Curtainwalls
Insurance Investigation for Claimants or Carriers
Insulating Glass Dew Point Testing
Follow us on Facebook or Twitter
and get daily updates you won't even see here!
Current client locations:
Alabama, Alberta, California, Florida, Georgia, Illinois, Indiana, Minnesota, Nebraska, New Jersey, New York, Nova Scotia, Ohio, Oklahoma, Ontario, Texas, Wisconsin.
Coming soon to your area
California, Florida, Georgia, New York
If you are in these areas and need help with your building, call now and save consultant travel expenses.
Scroll down for full background image.
- Windows for Buildings: Window Types & Materials
- Windows: Significant for Energy and Comfort
- Breaking Glass Shower Doors & Enclosures
- Glass Breakage and Pre-Existing Damage
- Restoring Steel Windows
- Deadly Falls from Windows: Preventable?
- Test Your Mettle at Construction Research Lab
- The Symbolic Value of Buildings
- Leaks and Problems with Vinyl Windows
- Envision the Wind in a Blizzard
- Insulated Glass Seal Failure
- Testing Leaking Brick Walls
- Window Condensation: Top 10 Fixes
- Leaks and Mold in Walls: the dirty little secret
- Choosing a Window Consultant or Exterior Building Consultant
- Leaks Through Split Face Block
- Storm Damage to Windows and Glass
- Bill Baker of Skidmore, Owings & Merrill LLP: Tall Buildings and the Burj Khalifa
- Fixing Window Leaks in Tall Buildings
- Designing Buildings for the Very Windy City
- Don’t miss Chicago Window Expert on Dateline NBC Tonight (Fri) 9/8c, The tragic fall of Josh Hilberling through the glass of his 25th floor apartment | Forum Events on About
- vinyl window replacement on Leaks and Problems with Vinyl Windows
- Jack on Leaks Through Split Face Block
- remodeling service on My Windows Leak!
- Tuhin on Window Repair or Window Replacement?
- vinyl window replacement on Leaks and Problems with Vinyl Windows
- Rabbi Weaselvich on The Symbolic Value of Buildings
- Ollie Buckley on Breaking Glass Shower Doors & Enclosures
- Robin I. Armstrong on Breaking Glass Shower Doors & Enclosures
- Horacio Cain on Breaking Glass Shower Doors & Enclosures
- Kaz on Glass Breakage and Pre-Existing Damage
- Courtney Wander on Window Condensation: Top 10 Fixes
- Courtney Wander on Historic Window Renovation
- Mark Meshulam on Test Your Mettle at Construction Research Lab
- Kaz on Test Your Mettle at Construction Research Lab
- agence immobiliere taroudant on Testing Leaking Brick Walls
- Mo on The Symbolic Value of Buildings
- Audrey on Breaking Glass Shower Doors & Enclosures
- John R. Barber on Breaking Glass Shower Doors & Enclosures
- Todd Elozory on Breaking Glass Shower Doors & Enclosures
Most Popular Posts
- My Windows Leak!: 47 comment(s) | 22453 view(s)
- Leaks and Problems with Vinyl Windows: 12 comment(s) | 12404 view(s)
- Window Glazing Leaks: 19 comment(s) | 11066 view(s)
- Diagnosing Glass Breakage: 24 comment(s) | 7031 view(s)
- Aluminum Window Leaks: 8 comment(s) | 6716 view(s)
- Window Condensation: Top 10 Fixes: 11 comment(s) | 6477 view(s)
- Annealed, Heat Strengthened, Tempered and Insulated Glass: 7 comment(s) | 5923 view(s)
- Window Sealant Failure: 18 comment(s) | 3683 view(s)
- Insulated Glass Seal Failure: 18 comment(s) | 3343 view(s)
- Preparing for a Window Leak Survey: 2 comment(s) | 3237 view(s)
- The Symbolic Value of Buildings: 4 comment(s) | 2737 view(s)
- Testing Leaking Brick Walls: 17 comment(s) | 2406 view(s)
- Leaks Through Split Face Block: 7 comment(s) | 2199 view(s)
- The Lowdown on Low-E Glass: 3 comment(s) | 2141 view(s)
- Deadly Falls from Windows: Preventable?: 16 comment(s) | 2067 view(s)
- Bill Baker of Skidmore, Owings & Merrill LLP: Tall Buildings and the Burj Khalifa: 4 comment(s) | 1921 view(s)
- Breaking Glass Shower Doors & Enclosures: 48 comment(s) | 1918 view(s)
- Designing Buildings for the Very Windy City: 11 comment(s) | 1724 view(s)
- Wood Window Leaks: 2 comment(s) | 1442 view(s)
- Curtainwall Leaks: 6 comment(s) | 1400 view(s)
- An Interview with Viracon: 4 comment(s) | 1380 view(s)
- Historic Window Renovation: 10 comment(s) | 1358 view(s)
- Chicago Energy Conservation Code for Dummies: 9 comment(s) | 1345 view(s)
- Field Museum Window Replacement: 2 comment(s) | 1330 view(s)
- Restoring Steel Windows: 6 comment(s) | 1194 view(s)
- Window Repair or Window Replacement?: 8 comment(s) | 1158 view(s)
- Leaks and Mold in Walls: the dirty little secret: 1 comment(s) | 1099 view(s)
- An Interview with Guardian: 4 comment(s) | 1082 view(s)
- The Future of Windows: 7 comment(s) | 1049 view(s)
- Thermal Images of Insulated Glass Types: 2 comment(s) | 990 view(s)
- Fixing Window Leaks in Tall Buildings: 5 comment(s) | 957 view(s)
- Welcome to Chicago Window Expert: 4 comment(s) | 906 view(s)
- An Interview with Historic Mike Jackson: 2 comment(s) | 891 view(s)
- Wynning in Glass Vegas: 3 comment(s) | 887 view(s)
- The Dynamic Water Test: 3 comment(s) | 652 view(s)
- Storm Damage to Windows and Glass: 0 comment(s) | 645 view(s)
- 2009 Web Statistics Revealed!: 4 comment(s) | 632 view(s)
- Test Your Mettle at Construction Research Lab: 22 comment(s) | 623 view(s)
- Choosing a Window Consultant or Exterior Building Consultant: 1 comment(s) | 572 view(s)
- Does Chicago Code Require Low-E Glass?: 5 comment(s) | 549 view(s)
- Glass Breakage and Pre-Existing Damage: 6 comment(s) | 505 view(s)
- Creating a Leak Survey Form: 4 comment(s) | 455 view(s)
- Documentary Photos for Curtainwall Survey: 0 comment(s) | 440 view(s)
- Legal Claims and Disputes in Construction: 0 comment(s) | 420 view(s)
- Performing Window Survey: 0 comment(s) | 401 view(s)
- An Interview with PPG: 1 comment(s) | 345 view(s)
- Chicago Window Expert Goes Solar: 8 comment(s) | 329 view(s)
- Fine Tuning Low-E Glass: 1 comment(s) | 316 view(s)
- Low-E Glass for Cooling Loads: 2 comment(s) | 283 view(s)
- Documentary Photos for Window Survey: 0 comment(s) | 270 view(s)